Varec Data Entry Terminal 8620 Installation and opertions Bedienerhandbuch Seite 13
- Seite / 40
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8620 Driver Entry Terminal
Varec, Inc. 5
2 Preparing for Installation
This chapter provides a site preparation checklist, safety information, unpacking instructions,
and installation instructions.
2.1 Site Preparation Checklist
Before installing the 8620 DET, ensure the following items:
• The use of a protective canopy or sunshade is recommended in order to shield the
driver entry terminal from direct sun, rain, and snow
• Adequate space for installation
• The appropriate communication lines back to the FuelsManager Oil & Gas Terminal
Automation system
• Power (AC or DC)
• Grounding
• Enclosure protection, such as concrete barrier poles to prevent trucks from damaging
the unit
2.2 General Safety Guidelines
The user shall follow safety guidelines provided by the Occupational Safety and Health
Administration (OSHA) for additional protection. Information may also be obtained from the
following sources:
• National Electrical Code (NEC)
• National Fire Protection Association (NFPA)
• Instrument Society of America (ISA)
• FM Approvals (FM)
• Underwriters Laboratories Incorporated (UL)
When in doubt about the safety of an area, check with the local safety authorities. Always
observe equipment labels and warning signs posted in the area.
2.3 Installation Safety Guidelines
This equipment should be installed only by qualified personnel familiar with the installation of
display and monitoring equipment.
Caution should be exercised when any area that is posted or otherwise assumed to contain
hazardous gases. Always follow OSHA guidelines.
To prevent shock hazards, the housing of all units should be properly grounded in accordance
with the National Electrical Code. A grounding conductor should be wired to the grounding
terminal provided on the 8620 DET.
! Warning Before attempting installation of the 8620 DET, review the “General Safety
Guidelines” section above. Installation and maintenance personnel should
become familiar with any hazards present as well as any agency requirements
before working with any equipment.
Obtain a hot work permit before performing maintenance on the 8620 DET with power applied.
- 8620 Data Entry Terminal 1
- Copyright 3
- Trademarks Acknowledged 3
- Product Approvals 3
- Disclaimer of Warranties 4
- Terms of Use 4
- Safety Precaution Definitions 5
- Safety Precautions 5
- Contents 7
- 1 Introduction 9
- 8620 Driver Entry Terminal 11
- Varec, Inc. 3 11
- Introduction 12
- 2 Preparing for Installation 13
- 2.4 Unpacking 14
- 2.5 Installation 14
- Varec, Inc. 7 15
- Preparing for Installation 16
- 3 Wiring 17
- Note: DIN Rail Wiring: 18
- Varec, Inc. 11 19
- 3.1.1 Power 20
- 3.1.2 Communications 20
- 3.2 Communications Wiring 21
- 4 Configuration 23
- Configuration 24
- 5.1 Maintenance 27
- 5.2 Troubleshooting 29
- 5.2.4 Replacing the Battery 31
- 5.2.6 Resetting the 8620 DET 32
- 6 Specifications 33
- 6.3 Host Communication 34
- 6.4 Environmental 34
- 6.5 Electrical 35
- 6.6 Mechanical Construction 35
- Specifications 36
- 7 Ordering Information 37
- Ordering Information 38
- Document Code 40
- IOM097GVAE4012 40
Verwandte Produkte und Handbücher für Vernetzung Varec Data Entry Terminal 8620 Installation and opertions
(40 Seiten)Tote Vision LCD-840D manuály
Uživatelské manuály a uživatelské příručky pro Monitory Tote Vision LCD-840D.
Poskytujeme 1 manuály pdf Tote Vision LCD-840D ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Kommentare zu diesen Handbüchern